YJ/TJ - T&T Full Replacement Tube Fender Give Away

[Scorpion]

To celebrate T&T Custom's completion of the YJ 4.5" wide front tube fender we've decided to give away a set to one lucky Co4x4 member the 31st of August.

http://www.tntcustoms.com/webv4/TJTubeFenderSamples/tjTubeFenderSample2.jpg

To Win:

You must be a Premium Colorado4x4.org Member - if you aren't, join/renew for $20 for a year by following this link: http://www.colorado4x4.org/vbb/showpost.php?p=129161&postcount=27
Put your name in the pot. Do do so, create a reply under the thread we have in the VIP section (http://www.colorado4x4.org/vbb/showthread.php?t=71418)for this give away.Good luck everyone!
Shipping will be free in the Denver Metro area (you get to meet me somewhere!)

Here's some information about the tube fenders for those of you who haven't seen them before:

The T&T Customs Full Replacement Front Tube Fender is designed to bolt-on to a stock YJ or TJ using nothing more than hand tools. They are full replacements so you can, if you so desire, recoup some of the cost (in this case make money) by selling your stock fenders because they get completely replaced.

The fenders are also designed to increase the wheel opening on your YJ to the rear of the wheel opening allowing you to run one size larger tire without suspesion mods. For those who are currently rubbing...this may be a really good thing!

Our fenders are fully welded, ship bare metal, and come complete with the hardware needed to install them.

Website info: http://www.tntcustoms.com/webV4/TJTubeFenders.asp

[Milo]

Is the only way to get yj ones, is to win them cuz I dont see them on your site anywhere??????

[Scorpion]

Is the only way to get yj ones, is to win them cuz I dont see them on your site anywhere??????

No sir! We're working on getting out the new website (it should have switched over a few minutes ago) and we'll be adding the YJ fenders to it very quickly (ASAP!!). The fenders look almost identical to the TJ fenders less a slight change at the grill mount. I'll get some pictures up as soon as I can.

They may be ordered by calling 307.775.9565.

Matt

[SoK66]

Hey, me three! Anxious to see the YJ version and will be intersted in buying as soon as they're available. I've got Clifton's on there right now. Great product, but I made a mistake and got the flare-less version which is not really very good for most stuff around here. I was going to simply add the flares on, but by the time I get the tubes bent & welded on, plus filling in the sheetmetal and re-painting it'll be more expensive than swapping them out for yours.

[4wdhunter]

Any plans to make a CJ7 tube fender?

[lilgreenjeepyj]

Any picts of the YJ setup???

[phattdraggon]

Any picts of the YJ setup???

X2 and whats the CO4x4 price? thanks for doing the give away.:beer:

[RockYacht]

Any plans to make a CJ7 tube fender?

Be patient, it's in the planning stages.

Bob

[Eric]

Just a reminder, TWO DAYS until the giveaway! :bounce:

[stewp97]

I won!

Thanks again to T&T custom for their support of the board and their awesome giveaways! I have wanted these for a long time! I can't wait to get them on jeep!


peter

[Eric]

I won!

Thanks again to T&T custom for their support of the board and their awesome giveaways! I have wanted these for a long time! I can't wait to get them on jeep!


peter
Congrats, and we want pics of them installed :D

[Chris Overacker]

All-right, good for you. Fine product too.

Here is a before pic:

http://code4x4.com/images/trips/trips_7_stewart_tj_21.jpg

Now, get-em-on and post an after pic!


(He will probably paint then screamin' yellow, whatcha bet?)

[stewp97]

All-right, good for you. Fine product too.

Here is a before pic:

http://code4x4.com/images/trips/trips_7_stewart_tj_21.jpg

Now, get-em-on and post an after pic!


(He will probably paint then screamin' yellow, whatcha bet?)
Only if the wife has any say in the matter (so yah, you are probably right :eek:)

[stewp97]

Well, the wife finally decided on a color!

http://www.colorado4x4.org/gallery/files/9/4/7/HC4W-Moab-11-06_51small.JPG

Thanks again to T&T for the awesome giveaway!

First trip out and no incidents. I'll have to try harder :D

peter

[jowwo]

Those look pretty cool with the "flare" painted on. I don't think I've seen any like that before.
Congrats!

[Chris Overacker]

The guys in my shop had the pleasure of installing these fenders. For the record, this is one of the finest products I've seen, installed and delt with. They fit perfectly and the finish was ready for paint. By the way, we painted them with spray-cans (NAPA color-matched it).

Good Job, guys (T&T).

[Taz]

Man I like the painted on flare look. That came out very nice. I also helped install a set a while back, and they were an easy install. I highly recommend those tube flares.