PDA

View Full Version : What do you do...

Tom N
September 28th, 2007, 11:14 PM
when you have to get rid of junk you have been collecting for 20 years?
Answer: Have fun with it.
Test your homemade cowcatcher with some perpendicular parking.
http://i157.photobucket.com/albums/t75/bbigtn/carCrush006600x450.jpg
Then make some car canoes.
http://i157.photobucket.com/albums/t75/bbigtn/carCrush008600x450.jpg
http://i157.photobucket.com/albums/t75/bbigtn/carCrush009600x450.jpg
http://i157.photobucket.com/albums/t75/bbigtn/carCrush011600x450.jpg
http://i157.photobucket.com/albums/t75/bbigtn/carCrush014600x450.jpg
http://i157.photobucket.com/albums/t75/bbigtn/carCrush015600x450.jpg
http://i157.photobucket.com/albums/t75/bbigtn/carCrush018600x450.jpg
http://i157.photobucket.com/albums/t75/bbigtn/carCrush019600x450.jpg
http://i157.photobucket.com/albums/t75/bbigtn/carCrush021600x450.jpg
http://i157.photobucket.com/albums/t75/bbigtn/carCrush022600x450.jpg
http://i157.photobucket.com/albums/t75/bbigtn/carCrush023600x450.jpg
http://i157.photobucket.com/albums/t75/bbigtn/carCrush026600x450.jpg
http://i157.photobucket.com/albums/t75/bbigtn/carCrush032600x450.jpg
http://i157.photobucket.com/albums/t75/bbigtn/carCrush033600x450.jpg
http://i157.photobucket.com/albums/t75/bbigtn/carCrush034600x450.jpg
http://i157.photobucket.com/albums/t75/bbigtn/carCrush036600x450.jpg
http://i157.photobucket.com/albums/t75/bbigtn/carCrush039600x450.jpg
jeepen
September 29th, 2007, 12:11 AM
Now thats some homemade redneck fun:D
creepycrawler
September 29th, 2007, 01:11 AM
I can't believe that you ran over that perfectly good tan & or light yellowish thing.

It looked like a perfectly good something.

:flipoff2:
Tom N
September 29th, 2007, 08:28 AM
The drivers side doors still open and shut.:shrug:
Whitey
September 29th, 2007, 10:21 AM
http://i157.photobucket.com/albums/t75/bbigtn/carCrush008600x450.jpg

Hey!

No tire stackin' :D


Those flattened cars in the background sure brings back memories for me.

Used to junk cars, cut the frames, pull the wires, pot metal, etc then raise a thick flat metal plate on on boom truck and drop the plate on em. Took about three times, then, load em on a flatbed and haul em to Pocatello.

Looks like a good time. :thumbsup:





.
Tom N
September 29th, 2007, 05:41 PM
Hey!

No tire stackin' :D


Those flattened cars in the background sure brings back memories for me.

Used to junk cars, cut the frames, pull the wires, pot metal, etc then raise a thick flat metal plate on on boom truck and drop the plate on em. Took about three times, then, load em on a flatbed and haul em to Pocatello.

Looks like a good time. :thumbsup:




.

Hey Whitey,it was fun alright.
I didn't stack tires going the other way after the first way went so well.:D
No worries about bending my driveshaft either since it already is.
Axle fixed?
http://i157.photobucket.com/albums/t75/bbigtn/carCrush018600x450.jpg
Whitey
September 30th, 2007, 01:07 AM
..........No worries about bending my driveshaft either since it already is.
Axle fixed? ........

Tomorrow!

Did my F-350 front axle and spindle bearings so far this weekend. They say to buy the whole spindle for $350 and not rebuild it, but, found the bearings at a bearing only place, so, just redid it.

Drivers side seal was a bear, but now it runs good as ever. :beer: :thumbsup:

EDIT: Tomorrow is today as I noticed the time.
Budman
September 30th, 2007, 09:30 AM
Hey looks like you are off the trail there. :flipoff2:
Tom N
September 30th, 2007, 10:10 AM
Tomorrow!

Did my F-350 front axle and spindle bearings so far this weekend. They say to buy the whole spindle for $350 and not rebuild it, but, found the bearings at a bearing only place, so, just redid it.

Drivers side seal was a bear, but now it runs good as ever. :beer: :thumbsup:

EDIT: Tomorrow is today as I noticed the time.


Good to know that can be done.:thumbsup:



Hey looks like you are off the trail there. :flipoff2:

Its a parking lot, not at a mall though! :D